Search results for: 'switch from test mode to run'

The Master Spa® Factory OEM 84" x 66" replacement hot tub cover is designed to fit your Master Spas® hot tub. This replacement custom hot tub cover is extremely energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full-length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.

The pivot arm for the CoverMate III is a direct OEM factory replacement for the original bar.

Replacement support arm for the CoverMate I Eco B and the inner support arm for the CoverMate Freestyle.

1/4 inch Washer for Oversized Snap Cap. These are the beauty caps that cover the screws that hold your side panels on. Available in 2 different sizes and 3 different colors.

The 11 amp, 2 speed 120 volt Pump is an insulated wet end pump designed as a replacement pump.

The Sensor, 24” x ¼” F/560 M7 is a high limit temp replacement sensor for the MAS560 sensor found in most Down East and Legend Series Master Spas.

Don’t let a broken sensor prevent you from your enjoying your spa when you want to.

Quickly and easily clean away dirt and debris from your pool and spa performance filters with the Power Pic Reach! The 100% aluminum nozzle with last you season to season and will save you money by preserving the life of your expensive filters!

The 70" x 83" Hot Tub Cover (Short-edge Fold) (SKU: 457187) is designed to fit your Master Spas® hot tub. This cover ensures extreme energy efficiency as it is made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal to help prevent heat loss. Additionally, it is made of a high end marine-grade vinyl covering that is mildew treated, and consists of upgraded rubber grip handles.

Note: This particular cover folds along the shortest 70-inch edge. For a hot tub cover folding on the long edge, please see 83" x 70" Hot Tub Cover (Long-edge Fold).

The 8' x 8' (94" x 94") Master Spas® hot tub replacement cover is a Master Spa Factory OEM replacement (SKU: X454888). It is specifically designed to fit your Master Spas® hot tub. This cover is energy efficient, as it's made of a thick 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and protects against UV rays.

The 7' x 6.5' (84" x 78") Master Spas® replacement hot tub cover (SKU: X454765) is a Master Spa Factory OEM replacement. It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.

The 66" x 78" Master Spas® factory direct OEM replacement hot tub cover (SKU: 66x78) is designed to fit your Master Spas hot tub. It comes standard with a 1.5lb foam density, long steam stopper cushions to help prevent any sort of heat loss. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

Note: This particular cover folds along the short edge. If you need a cover with these same dimensions (66" x 78") but that folds along the long edge, try our 66 × 78 Inch Hot Tub Cover (Long-edge fold).

This Master Spa Factory OEM 79" x 69" hot tub cover replacement (SKU: 457969) is specifically designed to fit your Master Spas® hot tub. This cover ensures energy efficiency as it consists of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal to help prevent heat loss. Additionally, it is made of a high end marine-grade vinyl covering that is mildew treated, and consists of upgraded rubber grip handles.

Note: This 79" x 69" hot tub cover folds along the long edge.