Search results for: 'washer foam strap cape'

Cooper Heater Strap. This is the shorter style of the 3 we have in stock (SKU #: 300016, SKU #: 300390). Copper construction provides easily installation for connecting your spa heater to the PC Board.

This is a copper jumper strap normally used with the ground wires in the spa. These are mounted on the back of the pumps connecting the ground wire. Is part of the connections from the heater to the PC Board.

Spa Cover Strap Loick Set

1/4 inch Washer for Oversized Snap Cap. These are the beauty caps that cover the screws that hold your side panels on. Available in 2 different sizes and 3 different colors.

Get rid of excess foam in your hot tub quickly and prevent foam from ruining your enjoyment and relaxation! SpaBoss Defoamer is safe to use even if you’re in the hot tub at the same time.

The custom factory OEM replacement 120” x 94” Master Spas® swim spa tub cover (SKU: X454108) is specifically designed to fit your Master Spas® hot tub. This swim spa cover has a six-inch thick foam insulation, which tapers down to four inches along the sides. This 24 R-value (the higher the R-value, the better the heat retention) energy-efficient cover comes with a 1.5lb foam density and long stopper steam cushions that help prevent heat loss, and upgraded rubber grip handles.

Note: This four-segment swim spa cover folds along the longest dimension (the 120" side).

The Master Spa® Factory OEM 78" x 78" (6.5') replacement hot tub cover (SKU: X457878) is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

.

The Master Spa® Factory OEM 84" x 70" replacement hot tub cover is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full-length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.

The Master Spa® Factory OEM 84” x 84” replacement hot tub cover has a 12" radius and is for Getaway Spas ONLY.

This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

The Master Spa® Factory OEM 6.5' x 6.5' replacement hot tub cover (SKU: X454065)is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full length heat seal cushions that help prevent heat loss, and two upgraded black rubber handles.

Over time, your spa or hot tub’s air controls may wear out, leaving you with less jetting action and much less enjoyment and relaxation. With the 1 Inch Molded Air Control (Grey), Master Spa Parts customers can affordably replace their air controls. This part is compatible with many models of Down East Spas, Freedom Spas, and the Master Spas® Legend Series.

The Master Spa® Factory OEM 82" x 60" replacement hot tub cover (SKU: x458260) is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6-inch thick foam insulation that tapers to 4-inch, full-length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

Note: This hot tub cover (82" x 60") folds along the long edge.