Search results for: 'cover master 1 spa coverm foam j 20'

This is the replacement Bushing for CoverMate I, CoverMate II and CoverMate III cover lifters. The Bushing is just $3.05 each and is sold here by Master Spa Parts. There is a reliability, ease of operation and ultimate beauty to the hydraulic cover lifts that can only be found in the CoverMate series. This part has SKU# 100344 and ships free when it is part of a total order $99 or more from Master Spa Parts.

Replacement support arm for the CoverMate I Eco B and the inner support arm for the CoverMate Freestyle.

The Master Spa® Factory OEM 84" x 70" replacement hot tub cover is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full-length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.

Thumbscrew 1/4 - 20 x 1.75 inch. These are used to secure your corner skirting pieces on your spa in place. This part is the longer of the two thumb-screws available.

Replacing fuses in your spa’s PC board is often a simple, straightforward solution to various problems that might arise with your spa or its features. The 20 Amp Power Input Fuse is a small piece in your spa’s PC board that allows your spa’s pumps to operate. Replacing this fuse allows you to continue to enjoy your spa and its features.

The Master Spas® hot tub replacement cover 70" x 84" is an exact Master Spa Factory OEM replacement (SKU: X457084). It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and protects against UV rays.

Note: This particular hot tub cover folds along the short edge. Find the corresponding long-edge fold cover here.

This left support arm for the CoverMate III is a powder coated replacement pivot arm of the original on your hot tub cover

*To determine if this is the correct replacement arm you need, look at your cover in the open position. While facing the spa and open cover lifter, the left arm is on the left side.*

The powder coated aluminum coupler for the CoverMate I, CoverMate II and CoverMate III is a direct replacement for the original bar.

The 108" x 94" Master Spas® replacement hot tub cover (SKU: X454994) is designed to fit your Master Spas® hot tub. This OEM factory hot tub cover comes with a 1. lb foam density, upgraded rubber grip handles and long steam stopper cushions to help prevent heat loss and make it extremely energy efficient!

Note: This cover folds along its longest dimension. 

The Master Spa® Factory OEM 84” x 84” replacement hot tub cover has a 12" radius and is for Getaway Spas ONLY.

This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

This Master Spa Factory OEM 78” x 78” hot tub cover replacement (SKU: X120240)  is specifically designed to fit your Master Spas® hot tub. This cover is energy efficient as it consists of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full length heat seal to help prevent heat loss. It is also made of a high end marine-grade vinyl covering that is mildrew treated, and consists of upgraded rubber grip handles.

This is the replacement right aluminum bracket or your CoverMate Cover Lifter by Leisure Concepts.

*To determine if this is the correct replacement bracket need, look at your cover in the open position. While facing the spa and open cover lifter, the right bracket is on the right side.*