Search results for: 'hot to drain my st'

Over time, your spa or hot tub’s air controls may wear out, leaving you with less jetting action and much less enjoyment and relaxation. With the 1 Inch Molded Air Control (Grey), Master Spa Parts customers can affordably replace their air controls. This part is compatible with many models of Down East Spas, Freedom Spas, and the Master Spas® Legend Series.

The custom factory OEM replacement 120” x 94” Master Spas® swim spa tub cover (SKU: X454108) is specifically designed to fit your Master Spas® hot tub. This swim spa cover has a six-inch thick foam insulation, which tapers down to four inches along the sides. This 24 R-value (the higher the R-value, the better the heat retention) energy-efficient cover comes with a 1.5lb foam density and long stopper steam cushions that help prevent heat loss, and upgraded rubber grip handles.

Note: This four-segment swim spa cover folds along the longest dimension (the 120" side).

The 84" x 94" Hot Tub Cover is a Master Spa Factory OEM replacement (SKU: x458494). It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

Note: This particular hot tub cover folds along its shortest dimension (the 84" side).

The pump marvel drains up to thirteen times faster than siphoning or draining! Unlike a garden hose, this pump does not lose its prime, and can lift and discharge water up to 20’ high. Don’t be fooled, the pump marvel is not a siphon, it’s a true pump! Please note that this pump does not take electricity.

The 108" x 94" Master Spas® replacement hot tub cover (SKU: X454994) is designed to fit your Master Spas® hot tub. This OEM factory hot tub cover comes with a 1. lb foam density, upgraded rubber grip handles and long steam stopper cushions to help prevent heat loss and make it extremely energy efficient!

Note: This cover folds along its longest dimension. 

The 7x7 Master Spas® hot tub replacement cover (84” x 84”) is a Master Spa Factory OEM replacment (SKU: X454777).

This cover fits other makes of Master Spa, and is the standard at 84" x 84" with a 6" radius.

This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

SpaBoss X-It makes it easy to switch sanitizers or to lower excessively high levels of chlorine or bromine in your spa or hot tub without having to drain and refill the whole thing.

Don’t let nasty oils and residue in your pool or spa create a scum line or clog your filter! Use Scumball to absorb and remove body oils and lotions to keep your pool or spa free from scum and prolong the life of your filter.

The Master Spas Freeze Plug Kit contains a plug set that works on most spa pumps. This can be loosened to drain any trapped fluid within your pump. Replacing a broken pump ? Make sure to get new freeze plugs as well.

Proline Jet Line Cleaner clears your hot tub jets of all unwanted organics, oils, residue, dirt, minerals and biofilm. It's a great way to keep your hot tub jets clean, clear, and working properly!

The Master Diverter Valve Handle is a genuine oem replacement part for your Master Spas hot tub. Diverter valves are made to redirect the water from your spa into different directions, as well as fully (or partially) shutting off your hot tub water flow. This specific diverter valve has a 2”inch handle and has an all over width of 4.5” inches.

1 1/2 inch SxSp Gate Valve