Search results for: 'vinyl spa cover'

The 6.5×7 Master Spas® (78" x 84") hot tub cover replacement (SKU: X454657) is specifically designed to fit your Master Spas® hot tub. This cover ensures energy efficiency as it consists of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal to help prevent heat loss. Additionally, it is made of a high end marine-grade vinyl covering that is mildew treated, and consists of upgraded rubber grip handles.

Note: This particular hot tub cover folds along the short edge. Find the corresponding long-edge fold cover here.

The 66" x 78" Master Spas® factory direct OEM replacement hot tub cover (SKU: 66x78) is designed to fit your Master Spas hot tub. It comes standard with a 1.5lb foam density, long steam stopper cushions to help prevent any sort of heat loss. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

Note: This particular cover folds along the short edge. If you need a cover with these same dimensions (66" x 78") but that folds along the long edge, try our 66 × 78 Inch Hot Tub Cover (Long-edge fold).

This 67" x 78" Hot Tub Cover (Short-edge Fold) hot tub cover replacement (SKU: 457969) is specifically designed to fit your Master Spas® hot tub. This cover ensures you energy efficiency as it is made of a 1.5-pound foam density, six-inch thick foam insulation that tapers to 4-inches along the sides, and a full-length heat seal to prevent heat loss. Additionally, it is made of a high-quality marine-grade vinyl covering that is mildew treated and protects against UV rays. Additionally, it boasts upgraded rubber grip handles.

Note: This particular hot tub cover folds along the shorter 67" edge. 

.

Swim Spa Filter Housing Weir Cover

PREMIUM UNDERMOUNT HOT TUB COVER LIFTER
-Works with all cover shapes
-Undermount design- no screwing into spa
-Gas spring assisted

**Swim spa kit available for units up to 54" tall

The Master Spa® Factory OEM 84" x 66" replacement hot tub cover is designed to fit your Master Spas® hot tub. This replacement custom hot tub cover is extremely energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full-length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.

The Master Spa® Factory OEM 82" x 60" replacement hot tub cover (SKU: x458260) is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6-inch thick foam insulation that tapers to 4-inch, full-length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

Note: This hot tub cover (82" x 60") folds along the long edge. 

The custom factory OEM replacement 120” x 94” Master Spas® swim spa tub cover (SKU: X454108) is specifically designed to fit your Master Spas® hot tub. This swim spa cover has a six-inch thick foam insulation, which tapers down to four inches along the sides. This 24 R-value (the higher the R-value, the better the heat retention) energy-efficient cover comes with a 1.5lb foam density and long stopper steam cushions that help prevent heat loss, and upgraded rubber grip handles.

Note: This four-segment swim spa cover folds along the longest dimension (the 120" side).

If replacing one suction cover, it is highly recommended that you replace all of them to be compliant. These suction covers are available for replacement of your older suction covers (spa models pre-2009). There is however no guarantee that these suction covers will fit your pre-2009 spa.

This left cover piece for the CoverMate III cover lifter snaps into the fitted location on the left side and covers all the pieces found there.

*To determine if this is the correct replacement cover pieceyou need, look at your hot tub cover in the open position. While facing the spa and open cover lifter, the left cover piece is on the left side.*

The right cover piece snaps into the fitted location on the right side and covers all the pieces on that side.

*To determine if this is the correct replacement cover piece you need, look at your hot tub cover in the open position. While facing the spa and open cover lifter, the right cover piece is on the right side.*

Adjust your cover height to your preference, with Ultralift’s Standard Mount hot tub cover. This mount allows you to have the option to increase privacy by having the cover up or store it behind your spa for optimal views.