Search results for: 'sp2 side off when power is temp on'

This is a OEM factory direct replacement rubber stopper smash cap for the CoverMate I hot tub cover. Easily replace your old smash cap with this replacement!

Boomerang brackets (1 pair) are specifically designed for use with the Visionlift Boomerang Cover Lifter by Ultralift. These brackets attach to your existing Ultralift sliding bracket, allowing your hot tub cover to fully open to the ground without the need for additional drilling. 

2 x 3/4 inch 6 Barb SxS Manifold

The Lounge/Small Corner Pillow will replace the hot tub pillow that came in your Master Spa hot tub when you first bought it.

The 2 Inch Diverter Handle - Black by Master Spas is a replacement for your home spa’s original water diverter valve handle. This piece is the lever that allows you to switch your water diverter valve off and on. Keeping your water diverter valves in good condition is important, as they allow you to control water flow in your spa.

The 84" x 94" Hot Tub Cover is a Master Spa Factory OEM replacement (SKU: x458494). It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

Note: This particular hot tub cover folds along its shortest dimension (the 84" side).

Washer for the regular sized Snap Caps. These are the beauty caps that cover the screws that hold your side panels on providing your spa with a professional beautiful finish.

This is the Plastic Bracket Right for CoverMate III and it is a replacement part for your CoverMate III Cover Lift. There is a reliability, ease of operation and ultimate beauty to the hydraulic cover lift that can only be found in the CoverMate III Cover Lift. This part retails for $47.20 here at Master Spa Parts.

**To determine if this is the correct replacement bracket you need, look at your cover in the open position. While facing the spa and open cover lifter, the right bracket is on the right side.**

A circuit board that's failed can put an end to your evenings of relaxation. We can help you bring back the good times with this Down East Spas and Master Spas® Circuit Board MAS425 PC Board (V/N 52364). Plus, you’ll spend much less than you would typically from your local repair shop! To make the offer even more attractive, our MAS425 replacement circuit board comes with free shipping to most United States locations (excluding Alaska and Hawaii).

The 8' x 17' cover (94" x 201") Master Spas® swim spa replacement cover is a Master Spa Factory OEM replacement part. All swim spa covers are made specifically to fit your Master Spas swim spa and come 6" thick in the middle and taper off to 4".  This cover includes an energy efficient 1.5 lb foam density and a 24 R-value, with a full length heat seal and upgraded rubber grip handles (included!). They are also available in 18 different colors.

The 8' x 15' (94" x 180") Master Spas® swim spa replacement cover is a Master Spa Factory OEM replacement (SKU: x454158). All swim spa covers are made specifically to fit your Master Spas swim spa and come 6" thick in the middle and taper off to 4".  This cover includes an energy efficient 1.5 lb foam density and a 24 R-value, with a full length heat seal and upgraded rubber grip handles (included!). They are also available in 18 different colors!

Measure the chemical balance of chlorine based water with AquaChek Chlorine 4-in-1 Test Strips in 15 seconds.

• Count: 50 test strips
• Tests for: Free Chlorine, pH, Total Alkalinity, Stabilizer (Cyanuric Acid)