Search results for: 'provid forc master spx getaway ocho rios cs'

The pivot arm for the CoverMate III is a direct OEM factory replacement for the original bar.

1/4 inch Washer for Oversized Snap Cap. These are the beauty caps that cover the screws that hold your side panels on. Available in 2 different sizes and 3 different colors.

Copper Heater Straps are used for connection of the Heater Unit of your spa to the Board within the Spa pack.

Easily installed.

The Master Spa® Factory OEM 78" x 78" (6.5') replacement hot tub cover (SKU: X457878) is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

.

Do you have one or more air controls that are causing you trouble in your hot tub or spa? This 1-Inch Air Control 2008 replacement part from Master Spa Parts can bring back the enjoyment of your hot tub. This spa air control replacement is suitable for the 2008 and 2009 models of Polaris, Fiji, and H2X Therapool spas.

This is the replacement Bracket Kit for CoverMate II and it can be screw-mounted low on the spa. The Bracket Kit for the CoverMate II is for a model that needs only 18 inches of clearance behind the spa in order to operate. There is a reliability, ease of operation and ultimate beauty to the hydraulic cover lift that can only be found in the CoverMate II Cover Lift. This part is sold for $73.45 here at Master Spa Parts.

Whether by chemical intrusion, moisture, or temperature fluctuations, circuit boards can and will fail. This may cause essential features, such as the spa lights, heaters, jets, and emergency shut-offs to not function as they should.

Savings, quality parts, and great service is what you can expect when replacing a circuit board, including this 5000 Daughter Board for Legend Series™ hot tubs by Master Spas®. This MS5000 external PCB (V/N 53544) and others priced $99 and over also qualify for fast and free shipping to buyers in the Continental United States.

The Extended Pivot Arm for CoverMate I is one of the parts that makes up this model of a hydraulic cover lifter. This Extended Pivot Arm has SKU# 100591 and is a replacement part for the CoverMate I, which is sold here by Master Spa Parts. It is recommended that you do not use the CoverMate I during high winds as to protect the cover and the hydraulic cover lifter from possible damage.

This is the replacement right aluminum bracket or your CoverMate Cover Lifter by Leisure Concepts.

*To determine if this is the correct replacement bracket need, look at your cover in the open position. While facing the spa and open cover lifter, the right bracket is on the right side.*

The 7' x 6.5' (84" x 78") Master Spas® replacement hot tub cover (SKU: X454765) is a Master Spa Factory OEM replacement. It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.

The 2 inch Pump Split Nut is used as a replacement for the pump union that would need to be re-plumbed. You can cut off the old pump union and replace with this split nut. This comes with the 2 screws that screw and hold it together.

The powder coated aluminum coupler for the CoverMate I, CoverMate II and CoverMate III is a direct replacement for the original bar.