Search results for: 'dimensions one sp2 ultra lift series'

The 8' x 15' Axis Swim Spa Cover for the H2X Trainer 15 Spas is a hassle-free cover for your swim spa! Made with high-tech rolling technology, this energy-efficient cover is effortless to operate, and it makes taking on and off your swim spa cover easier than ever. Available in dark gray Midnight. 

The 2 inch Standard Pump Union is a standard pump union used for complete assembly of your replacement pump. Should fit any 2 inch end on most pumps.

Spa circuit boards play a part in nearly every essential function of your spa or hot tub, everything from jets and temperature controls, to the safety switch-offs and lighting. So, when a board fails, you will likely see decreased function right away. Master Spa Parts aims to stock common and rare types of replacement circuit boards, including this MS2000 PC Board (V/N 52959) for Down East Spas and other brands.

If you're located in the Lower 48, you can also take us up on our free shipping offer on this printed circuit board replacement for MS2000 and many others found in our online store.

Designed for adding a beautiful finish to your spa, the expresso oversized snap cap goes over the screws that hold your spa side panels on. This unit is a dark espresso color.

General use 5/16 SS Washer from Master Spa Parts. This unit goes underneath fasteners on your spa/hot tub to keep components of your propulsion system intact.

The 8' x 19' Axis Swim Spa Cover for H2X Trainer 19 + Michael Phelps Momentum Spas is a hassle-free cover for your swim spa! Made with high-tech rolling technology, this energy-efficient cover is effortless to operate, and it makes taking on and off your swim spa cover easier than ever. Available in dark gray Midnight.

This is the replacement aluminum left bracket for your CoverMate cover lifter.

*To determine if this is the correct replacement bracket need, look at your cover in the open position. While facing the spa and open cover lifter, the left bracket is on the left side.*

This is a copper jumper strap normally used with the ground wires in the spa. These are mounted on the back of the pumps connecting the ground wire. Is part of the connections from the heater to the PC Board.

The 6.5×7 Master Spas® (78" x 84") hot tub cover replacement (SKU: X454657) is specifically designed to fit your Master Spas® hot tub. This cover ensures energy efficiency as it consists of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal to help prevent heat loss. Additionally, it is made of a high end marine-grade vinyl covering that is mildew treated, and consists of upgraded rubber grip handles.

Note: This particular hot tub cover folds along the short edge. Find the corresponding long-edge fold cover here.

The Master Spas® hot tub replacement cover 70" x 84" is an exact Master Spa Factory OEM replacement (SKU: X457084). It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and protects against UV rays.

Note: This particular hot tub cover folds along the short edge. Find the corresponding long-edge fold cover here.

The 7' x 6.5' (84" x 78") Master Spas® replacement hot tub cover (SKU: X454765) is a Master Spa Factory OEM replacement. It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.

The 8' x 8' (94" x 94") Master Spas® hot tub replacement cover is a Master Spa Factory OEM replacement (SKU: X454888). It is specifically designed to fit your Master Spas® hot tub. This cover is energy efficient, as it's made of a thick 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and protects against UV rays.