Search results for: 'Heaters spa master spa'
- Did you mean
- heaters sp1 master sp2
- heaters sp1 master sp1
- Related search terms
- spa cover 93" x 118"
- Master Spa - CLSEPRSET3 - Clarity & Healthy Living EPR Filter Set - (2) X268548 - PMA-R3 and PMA-EPR - (1) X268532
- Master Spa - X232607 - 1" Lighted Halo Air Control
- Master Spas - Topside Panel, MP900, No Overlay, For MS40 - X310203, 50305
- Master Spas, Down East, Emerald Spas Suction Drain Cover, 4-7/8 inch 0.D. VGB Law Compliant Replaced 0bsolete Original
This is the replacement part for the Plastic Bracket Left for CoverMate III for your CoverMate III Cover Lift. Our stylish composite mounting brackets combined with aluminum full-frame construction provides a perfect hydraulic cover lift option with no heavy lifting needed. This part is retails for $47.20 and is sold here at Master Spa Parts.
*To determine if this is the correct replacement bracket you need, look at your cover in the open position. While facing the spa and open cover lifter, the left bracket is on the left side.*
-
This is the Extended Pivot Arm for CoverMate III and it is a replacement part for your CoverMate III Cover Lift. There is a reliability, ease of operation and ultimate beauty to the hydraulic cover lift that can only be found in the CoverMate III Cover Lift. This part is 43 inches long and is sold here at Master Spa Parts.
-
The 7' x 6.5' (84" x 78") Master Spas® replacement hot tub cover (SKU: X454765) is a Master Spa Factory OEM replacement. It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.
Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.
-
The Master Spa® Factory OEM 78" x 78" (6.5') replacement hot tub cover (SKU: X457878) is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.
.
-
If replacing one suction cover, it is highly recommended that you replace all of them to be compliant. These suction covers are available for replacement of your older suction covers (spa models pre-2009). There is however no guarantee that these suction covers will fit your pre-2009 spa.
-
The 11 amp, 2 speed 120 volt Pump is an insulated wet end pump designed as a replacement pump.
-
The custom factory OEM replacement 120” x 94” Master Spas® swim spa tub cover (SKU: X454108) is specifically designed to fit your Master Spas® hot tub. This swim spa cover has a six-inch thick foam insulation, which tapers down to four inches along the sides. This 24 R-value (the higher the R-value, the better the heat retention) energy-efficient cover comes with a 1.5lb foam density and long stopper steam cushions that help prevent heat loss, and upgraded rubber grip handles.
Note: This four-segment swim spa cover folds along the longest dimension (the 120" side).
-
50/60Hz 12V DC Power Supply provides a regulated power source (up to 12V) to small appliances and devices with universal short-circuit protection. Designed and built to withstand the harsh conditions associated with use in spa and hot tub applications.
