Search results for: 'spa most spa cover remover'

The Master Spa® Factory OEM 84” x 84” replacement hot tub cover has a 12" radius and is for Getaway Spas ONLY.

This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

Spa Marvel Startup Kit

The Master Spas® hot tub replacement cover 70" x 84" is an exact Master Spa Factory OEM replacement (SKU: X457084). It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and protects against UV rays.

Note: This particular hot tub cover folds along the short edge. Find the corresponding long-edge fold cover here.

The Master Spa® Factory OEM 84" x 70" replacement hot tub cover is specifically designed to fit your Master Spas® hot tub. This replacement custom hot tub cover ensures energy efficiency as it consists of a 1.5lb foam density, 6 inch thick foam insulation that tapers to 4 inch, full-length heat seal cushions that help prevent heat loss, and upgraded black rubber handles.

Note: This particular hot tub cover folds along the long edge. Find the corresponding short-edge fold cover here.

The Ultralift Visionlift Boomerang cover lifter (SKU: 6132034) gives you the freedom to open your cover all the way to the ground. With this cover lifter and sliding bracket, you will not have to drill a second location on your spa cabinet for your lifter.

If replacing one suction cover, it is highly recommended that you replace all of them to be compliant. These suction covers are available for replacement of your older suction covers (spa models pre-2009). There is however no guarantee that these suction covers will fit your pre-2009 spa.

The Master Spas Freeze Plug Kit contains a plug set that works on most spa pumps. This can be loosened to drain any trapped fluid within your pump. Replacing a broken pump ? Make sure to get new freeze plugs as well.

Extend the life of your spa cover with Spa Ease Cover Conditioner!

This Master Spa Factory OEM 78” x 78” hot tub cover replacement (SKU: X120240)  is specifically designed to fit your Master Spas® hot tub. This cover is energy efficient as it consists of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full length heat seal to help prevent heat loss. It is also made of a high end marine-grade vinyl covering that is mildrew treated, and consists of upgraded rubber grip handles.

This left cover piece for the CoverMate III cover lifter snaps into the fitted location on the left side and covers all the pieces found there.

*To determine if this is the correct replacement cover pieceyou need, look at your hot tub cover in the open position. While facing the spa and open cover lifter, the left cover piece is on the left side.*

Our Master Spas® 83" x 70" hot tub cover (SKU: 458771) is a factory direct OEM replacement cover specifically designed to fit your Master Spas® hot tub. Consisting of 1.5lb foam density, long steam stopper cushions, six-inch foam insulation, four inch tapered sides, upgraded rubber grip handles and a 24-R value (the greater the R-value, the better the heat storage and heat retention), this cover prevents heat loss and is extremely energy efficient.

Note: This hot tub cover folds along the long edge.

The right cover piece snaps into the fitted location on the right side and covers all the pieces on that side.

*To determine if this is the correct replacement cover piece you need, look at your hot tub cover in the open position. While facing the spa and open cover lifter, the right cover piece is on the right side.*