Search results for: 'clean spas topside control 1996 4.0 1 pump system'

This Master Spa Factory OEM 66" x 84" hot tub cover replacement (SKU: X456684) is specifically designed to fit your Master Spas® hot tub. This cover ensures energy efficiency as it consists of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal to help prevent heat loss. Additionally, it is made of a high end marine-grade vinyl covering that is mildew treated, and consists of upgraded rubber grip handles.

Note: This particular hot tub cover folds along the short edge. Find the corresponding long-edge fold cover here.

This is the Extended Pivot Arm for CoverMate III and it is a replacement part for your CoverMate III Cover Lift. There is a reliability, ease of operation and ultimate beauty to the hydraulic cover lift that can only be found in the CoverMate III Cover Lift. This part is 43 inches long and is sold here at Master Spa Parts.

The Ultralift Undermount conversion kit allows for you to change your standard cover lift into one with an undermount. With this undermount, there is no more drilling into the side of your spa to install a cover lifter. This is bought in addition to a Ultralift cover lifter.

The 66" x 78" Master Spas® factory direct OEM replacement hot tub cover (SKU: 66x78) is designed to fit your Master Spas hot tub. It comes standard with a 1.5lb foam density, long steam stopper cushions to help prevent any sort of heat loss. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated and unfazed by UV rays.

Note: This particular cover folds along the short edge. If you need a cover with these same dimensions (66" x 78") but that folds along the long edge, try our 66 × 78 Inch Hot Tub Cover (Long-edge fold).

The 78" x 66" Hot Tub Cover (Long-edge Fold) is an exact Master Spa Factory OEM replacement. It is specifically designed to fit your Master Spas® hot tub. This cover is extremely energy efficient, as it's made of a 1.5-pound foam density, six-inch thick foam insulation (which tapers to 4-inches along the sides), and a full-length heat seal. It has been upgraded to include two rubber grip handles and is made of a high quality marine-grade vinyl covering that is mildew treated.

Note: This particular cover folds along the longer 78" edge. If you need a cover with these same dimensions (66" x 78") but that folds along the short edge, try our 66 × 78 Inch Hot Tub Cover (Short-edge fold).

This is the H2X Shaft Pin with SKU number X400130 and is one element that goes with the Blade Prop Kit. The H2X Shaft pin is a prop shaft pin and is a component of the wave propulsion.

This support arm lower for CoverMate Easy by Leisure Concepts is a direct OEM replacement for your original hot tub cover support arm.

With Scumball, you can remove all those body oils, suntan lotions, and oily scented products that form a scum line on the surface of your pool or spa. These scum-beating balls can absorb up to 40 times their own weight with all those oils and lotions!

This right support arm for the CoverMate III is a powder coated replacement pivot arm of the original on your hot tub cover.

*To determine if this is the correct replacement arm you need, look at your cover in the open position. While facing the spa and open cover lifter, the right arm is on the right side.*

This left support arm for the CoverMate III is a powder coated replacement pivot arm of the original on your hot tub cover

*To determine if this is the correct replacement arm you need, look at your cover in the open position. While facing the spa and open cover lifter, the left arm is on the left side.*

The Shock Non-Locking for CoverMate III Eco B is one of the parts that make up this economically efficient choice for a hydraulic cover lifter. The Shock Locking connects to the shock itself. It is recommended that you do not use the CoverMate III Eco B during high winds as to protect the cover and the hydraulic cover lifter from possible damage.

The Original Swim Tether is designed to provide a unique resistance workout for swimmers of all skill levels. Quickly install and assemble to swim in most swim spas and swimming pools. A minimum of fourteen feet of swim space is recommended. Using optimal lift and an elevated connection point allows the swimmer to swim unencumbered by cords and restrictive ankle attachments.